Cleaning your PS5 controller can seem daunting, especially for first-timers. With many screws and delicate components, it's crucial to take a methodical and careful approach. This guide will walk you through the process step-by-step, with tips to make it beginner-friendly.

Nødvendigt værktøj og materialer

Screwdriver: Phillips PH00 with a magnetic tip (ideal for small screws).
Plastic Pry Tool: Til sikker åbning af dele uden ridser.
Tweezers: For handling small parts and debris.
Soft Brush: A toothbrush with soft bristles works well.
Bomuldsknopper: Til præcis rengøring af trange rum.
Mikrofiberklud: Til rengøring af udvendige overflader uden at ridse.
Isopropyl Alcohol (70% or higher): Safe for electronic components.
Compressed Air Can or Air Blower: For removing fine dust particles.
Plastbeholdere eller bakker: Til at organisere skruer og komponenter.

Step-by-Step Instructions

Step 1: Prepare Your Workspace

Work on a clean, flat surface with plenty of light.
Place a soft mat or cloth underneath to protect components.
Keep tools and materials organised for easy access.

Step 2: Remove the Black Faceplate

Brug et plastikværktøj til at løfte den sorte frontplade nær de analoge pinde.
Gently work your way around the edges until the faceplate pops off.

Step 3: Locate and Remove the Screws

Der er fire skruer, der holder controlleren sammen:
Two under the L1 and R1 buttons. Use a pry tool to lift these buttons and expose the screws.
To i de nederste hjørner, afsløret efter fjernelse af frontpladen.
Use a Phillips PH00 screwdriver to remove these screws and set them aside.

Step 4: Detach the Back Cover

The back cover is secured by two clips near the speaker area.
Use a plastic pry tool to gently release the clips.
Once loosened, place the controller analogue sticks down to expose the battery.

Step 5: Remove the Battery

Frakobl batteriet ved at trække det opad med fingrene eller en pincet.
Place it in a safe area away from your cleaning station.

Step 6: Unscrew the Battery Casing

A single screw holds the battery casing in place. Remove it with the PH00 screwdriver and set it aside.

Step 7: Disconnect Ribbon Cables

Locate the ribbon cables connecting the motherboard and gently disconnect them.
Use tweezers to pull the cables straight upwards to avoid damage.

Step 8: Remove Additional Screws and the Motherboard

Skru de to skruer, der fastgør bundkortet på venstre og højre side af.
Carefully lift the motherboard, being cautious of the attached vibration motor wires.

Step 9: Clean Internal Components

Rengøring af knapområdet og Flex PCB

After removing the motherboard, locate the DualSense Flex PCB (Printed Circuit Board), which connects to the buttons.
The buttons are held in place by a plastic retainer. Carefully remove this retainer to expose the button membranes and the contact points.
Each button has a black circular conductive pad underneath that makes contact with the Flex PCB. If these areas become dirty, the buttons may stop responding.
Brug en vatrondel dyppet i isopropylalkohol til at rense de sorte ledende puder og kontaktpunkterne på Flex PCB.
Allow the alcohol to evaporate fully before reassembly.

Dust and Hair Removal

Use tweezers or a soft brush to remove dust and hair from inside the controller.

Alkohol rengøring

Påfør isopropylalkohol på en vatpind, og rengør forsigtigt de analoge mekanismer, udløserkomponenter og andre svært tilgængelige områder.

Compressed Air

Use a compressed air can or air blower to clear out remaining dust and ensure the components are dry.

Step 10: Clean the Buttons and External Surface

Button Cleaning

Fjern knapperne (f.eks. X, Square, Circle, Triangle, D-pad) fra plastikholderen.
Soak the buttons in isopropyl alcohol for a few minutes to loosen dirt.
Brug en blød børste eller mikrofiberklud til at rengøre knapperne grundigt.

Cleaning the Outer Casing

Use a microfibre cloth with isopropyl alcohol to clean the grips, seams, and external surfaces.
Focus on areas where sweat and dirt accumulate.
Til trange steder skal du bruge en vatpind eller et plastikplukkerværktøj til at rense rundt om kanterne.

Professionelle tips til nybegyndere

Take Photos: Document each step to remember where components, screws, and parts belong.
Vær tålmodig: Undgå at haste; tvingende komponenter kan forårsage skade.
Brug magnetiske værktøjer: Magnetiske skruetrækkere hjælper med at forhindre, at skruer tabes på trange steder.
Test as You Go: After reassembly, test each button and function before fully closing the controller.

Step 11: Reassemble the Controller

Reconnect ribbon cables and secure the motherboard with screws.
Placer knapperne tilbage i plastikholderen, og sørg for, at de flugter korrekt med de sorte ledende puder og Flex PCB.
Reattach the battery casing and battery.
Klik bagdækslet og den sorte frontplade på plads igen.

Final Check

Efter genmontering, test controlleren grundigt. Sørg for, at knapper, triggere og analoge sticks fungerer problemfrit. Med øvelse og tålmodighed har du en perfekt rengjort controller klar til handling!

If you CBA, get it done by the repair OGs at OG Repairs

Sådan renser du din PS5 Controller: En begyndervenlig guide