Cleaning your PS5 controller can seem daunting, especially for first-timers. With many screws and delicate components, it's crucial to take a methodical and careful approach. This guide will walk you through the process step-by-step, with tips to make it beginner-friendly.

Tools and Materials Needed

Screwdriver: Phillips PH00 with a magnetic tip (ideal for small screws).
Outil de levier en plastique : pour ouvrir les pièces en toute sécurité sans rayures.
Tweezers: For handling small parts and debris.
Soft Brush: A toothbrush with soft bristles works well.
Cotton Buds: For precise cleaning of tight spaces.
Microfibre Cloth: To clean external surfaces without scratching.
Isopropyl Alcohol (70% or higher): Safe for electronic components.
Compressed Air Can or Air Blower: For removing fine dust particles.
Plastic Containers or Trays: To organise screws and components.

Step-by-Step Instructions

Step 1: Prepare Your Workspace

Work on a clean, flat surface with plenty of light.
Placez un tapis ou un chiffon doux en dessous pour protéger les composants.
Keep tools and materials organised for easy access.

Step 2: Remove the Black Faceplate

Use a plastic pry tool to lift the black faceplate near the analogue sticks.
Travaillez doucement sur les bords jusqu'à ce que la façade se détache.

Step 3: Locate and Remove the Screws

Il y a quatre vis qui maintiennent le contrôleur ensemble :
Two under the L1 and R1 buttons. Use a pry tool to lift these buttons and expose the screws.
Two at the bottom corners, revealed after removing the faceplate.
Use a Phillips PH00 screwdriver to remove these screws and set them aside.

Step 4: Detach the Back Cover

The back cover is secured by two clips near the speaker area.
Use a plastic pry tool to gently release the clips.
Once loosened, place the controller analogue sticks down to expose the battery.

Step 5: Remove the Battery

Disconnect the battery by pulling it upwards using your fingers or tweezers.
Place it in a safe area away from your cleaning station.

Step 6: Unscrew the Battery Casing

Une seule vis maintient le boîtier de la batterie en place. Retirez-le avec le tournevis PH00 et mettez-le de côté.

Step 7: Disconnect Ribbon Cables

Locate the ribbon cables connecting the motherboard and gently disconnect them.
Use tweezers to pull the cables straight upwards to avoid damage.

Step 8: Remove Additional Screws and the Motherboard

Unscrew the two screws securing the motherboard on the left and right sides.
Carefully lift the motherboard, being cautious of the attached vibration motor wires.

Step 9: Clean Internal Components

Cleaning the Button Area and Flex PCB

After removing the motherboard, locate the DualSense Flex PCB (Printed Circuit Board), which connects to the buttons.
Les boutons sont maintenus en place par un support en plastique. Retirez délicatement ce dispositif de retenue pour exposer les membranes des boutons et les points de contact.
Each button has a black circular conductive pad underneath that makes contact with the Flex PCB. If these areas become dirty, the buttons may stop responding.
Utilisez un coton-tige imbibé d'alcool isopropylique pour nettoyer les pastilles conductrices noires et les points de contact du Flex PCB.
Allow the alcohol to evaporate fully before reassembly.

Dust and Hair Removal

Utilisez une pince à épiler ou une brosse douce pour enlever la poussière et les cheveux de l'intérieur du contrôleur.

Alcohol Cleaning

Apply isopropyl alcohol to a cotton bud and gently clean the analogue mechanisms, trigger components, and other hard-to-reach areas.

Compressed Air

Use a compressed air can or air blower to clear out remaining dust and ensure the components are dry.

Step 10: Clean the Buttons and External Surface

Nettoyage des boutons

Remove the buttons (e.g., X, Square, Circle, Triangle, D-pad) from the plastic retainer.
Faites tremper les boutons dans de l'alcool isopropylique pendant quelques minutes pour éliminer la saleté.
Use a soft brush or microfibre cloth to clean the buttons thoroughly.

Cleaning the Outer Casing

Use a microfibre cloth with isopropyl alcohol to clean the grips, seams, and external surfaces.
Focus on areas where sweat and dirt accumulate.
For tight spots, use a cotton bud or a plastic picker tool to clean around the edges.

Pro Tips for First-Timers

Prenez des photos : documentez chaque étape pour vous rappeler où appartiennent les composants, les vis et les pièces.
Soyez patient : évitez de vous précipiter ; forcer les composants peut causer des dommages.
Utilisez des outils magnétiques : les tournevis magnétiques aident à éviter de perdre des vis dans des espaces restreints.
Test as You Go: After reassembly, test each button and function before fully closing the controller.

Step 11: Reassemble the Controller

Rebranchez les câbles plats et fixez la carte mère avec des vis.
Place the buttons back into the plastic retainer, ensuring they align correctly with the black conductive pads and the Flex PCB.
Reattach the battery casing and battery.
Snap the back cover and black faceplate back into place.

Vérification finale

After reassembly, test the controller thoroughly. Ensure the buttons, triggers, and analogue sticks function smoothly. With practice and patience, you'll have a perfectly cleaned controller ready for action!

Si vous CBA, faites-le faire par les OG de réparation à OG Repairs

Comment nettoyer votre PS5 Contrôleur : un guide convivial pour les débutants